• 목록
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

However, this depends on the IC 232 chip selection and not in the TIA-232 standard specifications. How do you compare and evaluate different LDO specifications and datasheets? Q: How does RS422 compare to RS485 in terms of communication capabilities? The transmitter and receiver compare the voltages of the data- and handshake lines with one common zero line. One of the main problems with RS232 is the lack of immunity for noise on the signal lines. The picture shows the magnetic field lines and the noise current in the RS485 data lines that is the result of that magnetic field. In the straight cable, all noise current is flowing in the same direction, practically generating a looping current just like in an ordinary transformer. Multimeter: You can use it to measure voltage and current on the RS485 lines, aiding in identifying wiring issues. RS422 also has stricter voltage requirements than RS485.

In this article, we take a comparative tour of RS485 and RS232 based on their operating distance, electrical signaling techniques, data rates, number of drivers and receivers, and voltage requirements. RS232 is an interface to connect one DTE, data terminal equipment to one DCE, data communication equipment at a maximum speed of 20 kbps with a maximum cable length of 50 feet. LIMITATIONS 1. Jamie Mascola is correct, speed can reach 3 Mbps. It operates at a maximum data rate of 10 Mbps and can transmit data over long distances of up to 1200 meters. RS485 is a good choice for connecting multiple devices over a long distance and high speed with some complexity and cost. RS422 should be considered if you need to connect one device to multiple devices over a long distance and high speed with full-duplex communication. In most higher level protocols, one of the nodes is defined as a master which sends queries or commands over the RS485 bus.

USB to UART convertor cables have RS485 level UART signals plus offer you a quick and simple path connecting to an RS485 interface to USB. RS485 can have a cable length of up to 1200 meters(data rate is limited to 100kbps), useful for connecting distant devices. RS422 is faster (up to 10 Mbps) and longer-distance (up to 1200 meters) than RS232, and less noisy than RS485. RS485 is fast (up to 10 Mbps), long-distance (up to 1200 meters), and noise-resistant, making it suitable for industrial and network applications. It is an industry-standard that allows for fast and efficient communication between multiple devices using two-wire connections. That is why RS485 is currently a widely used communication interface in data acquisition and control applications where multiple nodes communicate with each other. This FTDI converter cable provides a fast, simple way to connect devices with an RS485 interface to USB. Each FTDI USB-RS485 cable contains a small internal electronic circuit board utilizing the FT232R that is encapsulated into the USB connector end of the cable. FTDI USB to RS485 Serial UART Converter Cable incorporates FTDI's FT232RQ USB to serial UART interface IC, which handles all the USB signaling and protocols.

Apart from a one-to-one connection, RS485 can be used with a serial bus that connects to multiple peripherals. RS-232/ Recommended Standard-232 was introduced in the 1960s, and after going through multiple revisions, it was named TIA/EIA -232-F in 1977. Electronic Industries Association (EIA) and Telecommunications Industries Association (TIA) are in charge of edifying the standard. Wide Adoption and Compatibility: RS-485 is a well-established and widely adopted standard. Suitable for Multi-Vendor Environments: The standardization of RS-485 ensures interoperability between devices from different vendors. RS232 is easy to implement and widely supported by many devices and software applications. But some of the other interfaces are certainly interesting because they can be used in situations where RS232 is not appropriate. The equipment located along a set of RS-485 wires are interchangeably called nodes, stations or devices. RS422 stands for Recommended Standard 422, and it was derived from RS485 in 1978. It is a point-to-multipoint protocol, which means that it can connect one transmitter and up to 10 receivers using a single pair of wires. The biggest drawback with 422 is the lack of standard implementation. RS485 Converter: Rs485 converter converts between RS485 and other communication protocols like RS232, USB, or Ethernet.

For more info about rs485 cable look into the web page.